DIY Install: T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector on your 2009 Kia Sedona скачать в хорошем качестве

DIY Install: T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector on your 2009 Kia Sedona

Click for more info and reviews of this Tekonsha Custom Fit Vehicle Wiring: https://www.etrailer.com/Custom-Fit-V... Check out some similar Custom Fit Vehicle Wiring options: https://www.etrailer.com/fitguidet1.htm Search for other popular Kia Sedona parts and accessories: https://www.etrailer.com/vehicle/2009... https://www.etrailer.com Don’t forget to subscribe!    / etrailertv   Full transcript: https://www.etrailer.com/tv-install-t... Speaker 1: Today on our 2009 Kia Sedona, we're going to be taking a look at and showing you how to install the Tekonsha T1 Vehicle Wiring Harness with Four Pole Flat Trailer Connector, part number 118410.This is what our wiring looks like when it's installed. This is going to give you all the necessary functions for your trailer lighting. Your turn signals, your brake lights, your running lights, and your ground. Going to come with a dust cap to help cover your connections, keep it from corroding. When not in use, you can second your dust cap as a holder, like that, on your safety chain loops. If you prefer to have it mounted and stationary on the hitch, we do have long brackets, short brackets, and four pole holders, which you can find on our website.First thing we need to do to start our installation, we need to gain access to our taillights. You're going to have three screws we need to remove to remove our taillights. You're going to do the same thing on both sides of the vehicle. We'll be using a Philips screwdriver. We're going to slowly start to pry this out. We're going to unhook our wiring right down here that's run into the vehicle. We're going to push down on this little tab and pull out, like that. We'll set our light aside for re-installation. Now we'll go over to our passenger side and do the same thing.You can see right here, I ran an airline tube down behind my bumper and it's coming out the bottom by my hitch. What you're going to have to do is you're going to have to find a path that goes down through there. Next thing I'm going to do is I'm going to take my wire with the yellow, brown and white, I'm going to tape it on the end of my airline tube with some electrical tape, like this. I'm going to slowly pull it back up through here.Once you get your path through, pull your wires out. We'll remove the wiring from the airline tube. What we're going to do is we're going to match the ends, push it in until you hear it click. Now we can reinstall our taillight and put that onto our taillight. Push it in until you hear it click. You want to make sure that you line up the pins with the holes in the side as you're putting it in. Now we can reinstall our screws that we removed.The next thing we're going to is, right here on the bottom underneath the vehicle there's a plastic panel. There's one, two, three, four plastic screws that are Philips that we're going to remove before we run our green wire across the bumper. We're going to take our green wire that's running to our passenger side light and we're going to push it up back up in there. Then we're going to put our screws back in, and that's going to hold our wire up inside of our bumper fascia, up in here.Next, we're going to do the same thing we did on our driver side. We're going to take our wiring, it's going to be the green and red. We're going to hook it onto our airline tube that's running up to the body of the vehicle. Then we're just going to repeat our process on pulling it up.Next what I'm going to do is my modular box, I need to find a good place to mount it. What I did is, right up on the back side of this pan here there's a nice flat spot. What I'm going to do, I'm going to take some rubbing alcohol and I need to wipe off the back of the box, make sure it's clean. Then the spot where I'm going to be placing it, I need to make sure that is clean. Next, I'll take my two-sided tape, peel off one end and put it on my box. Peel off the other end. Once you get it in the spot, make sure you press it into place.Next thing I'm going to do is connect my power wire. My black wire that I'm going to be running to the front, I want to take up and you can see I've made kind of a little half moon shape out of it. I want to run it behind my bracket that's holding the rest of my wires in, just like that. Going to take my red wire over the top. Now we'll strip our power wire that we're running to the front.Now, your kit comes with butt connectors however, I'm going to replace it with a heat shrink butt connector since this is going to be living outside the vehicle, it's going to give it a little extra protection. Crimp it down and we'll connect it onto our red wire, crimp it down. Take a heat gun and we will shrink up the butt connector. Once you have it shrunk, we'll take some electrical tape, we'll wrap it up just to give it a little extra protection. Then we'll slowly start to pul