Roland S-50 - Key bed Repair - Restoration Part 5 скачать в хорошем качестве

Roland S-50 - Key bed Repair - Restoration Part 5

In Part 5 I turn my attention to what do I need to do to the Roland S-50 key bed to try and restore the key bed back to full operation. I know that 2 of the keys on the keyboard are dead. So we know that this is an issues that need to be repaired, in addition to any other issues I now identify. The first task is to remove the glue used to attach the plastic key locks and also the material used to lock the keys against the keyboard frame. Label remover to lift the residue and IPA to degrease the area after the residue has been removed. Next I removed the rubber strip key contacts that sit on top of the graphic contacts on the circuit board. Finally in this episode I remove the glue from the plastic key locks ready for re-installation in a later episode. Background I acquired the Roland S-50 a few years ago after I had been on the hunt for a low-fi sampler. This fitted the bill sampling at 12-bits. Not only is the Roland S-50 a fairly useable sampler, Roland and many other software / sampling vendors also crafted sample sets for both this and the Roland S-550 / Roland S-330 platforms. When acquired there were a few problems. Apart from the sampler being filthy, some keys either did't work or work intermittently and the screen randomly choose not to work. What I didn't know when I started this project was how involved it would get! Equipment and supplies used: Electrolube (LRM) Label remover https://themusictechguyuk.me/3JUr9jw Isopropyl-Alcohol (IPA) https://themusictechguyuk.me/3C23Ke9 Plastic razor scraper https://themusictechguyuk.me/3STmkef The equipment mentioned above (if you can still buy it!): Roland S-50 (Used): https://themusictechguyuk.me/3b3CQUo 📖Chapters: 00:00 Opening 00:22 What do I think needs to be done? 04:39 Channel promotion 05:02 Removing the residual glue 08:35 Remaining glue removal and degreasing the area 13:16 Removing the 'Roland' rubber key contacts 16:49 Rubber contact condition assessment 18:26 Cleaning plastic keylocks - glue removal 19:57 Part 5 summary #RolandS50 #RolandS50Sampler #S50 Videos in this Series: Part 1:    • Roland S-50 - What to do next? - Restorati...   Part 2:    • Roland S-50 - How to get into the sampler ...   Part 3:    • Roland S-50 - Front Panel Repairs - Restor...   Part 4:    • Roland S-50 - Key bed Strip Down - Restora...   Part 5:    • Roland S-50 - Key bed Repair - Restoration...   Part 6:    • Roland S-50 - Rust Removal - Restoration P...   Part 7:    • Roland S-50 - Circuit board repairs and st...   Part 8:    • Roland S-50 - Key bed reassembly - Restora...   Part 9:    • Roland S-50 - Recapping the power board - ...   Part 10:    • Roland S-50 - Re-fitting the power board -...   Part 11:    • Roland S-50 - 2nd Keyboard strip down and ...   Part 12:    • Roland S-50 - 2nd Keyboard strip down and ...   Part 13:    • Roland S-50 - Fitting the new powerboard  ...   Part 14:    • Roland S-50 - Completion for NOW! - Restor...   For less than the price of a cup of coffee, support The Music Tech Guy UK channel, join the TMTG community: http://themusictechguyuk.me/Community 🎼The Music Tech Guy UK can be found in the following places: Youtube:    / @themusictechguyuk   Website: https://www.themusictechguyuk.com Patreon: http://themusictechguyuk.me/Community Facebook:   / themusictechguyuk   Instagram:   / themusictechguyuk   X: https://X.com/MusicTechGuyUK Tumblr: https://www.tumblr.com/dashboard/blog... Don't confuse the The Music Tech Guy UK or Music Tech Guy UK with copycat channels. There is only one me! Roland S50 - Key bed Repair - Restoration Part 5 - 2022-08-16